首页 > 工程物探测绘 >  阴极防护/腐蚀控制 > 腐蚀控制产品 > 环氧树脂涂料 > Tapecoat7025环氧涂料
Tapecoat7025环氧涂料
Tapecoat7025环氧涂料
订货号: MM-80550-00
产地: 美国
品牌:
开发编号: N
市场价:
*此产品根据配置不同价格不同
*此价格为参考价格,具体价格以订单合同为准
    我在现场:
    产品视频:
  • 产品描述
  • 技术参数
  • 技术文档
  • 相关产品
  • 明细价格
  • 购买流程
产品描述:

Description
Tapecoat TC® 7025 EZ FLOW EPOXY is a versatile liquid epoxy for the protection of pipe and metal structures from corrosion in both above and below grade environments. It is a two-part liquid epoxy system can be used as a one-coat stand-alone protective coating to isolate the metal substrate from the detrimental effects of electrolysis. It is an environmentally friendly, 100% solids coating that contains no VOC’s (volatile organic compounds).
TC 7025 provides exceptional corrosion prevention for protecting joints, patching pipeline coatings, and covering irregular fittings and metal surfaces. This innovative product can be used in conjunction with all factory and field coatings, such as cold and hot applied tape, coal tar enamel, extruded polyethylene, and fusion bonded epoxy. It is applied to a dry, properly prepared surface, either manually or with the use of a power spray unit designed for such purpose. It can be applied to a thickness up to 25 mils, providing a tough resistant barrier when exposed to backfill and soil stress. It is an easy alternative to the complex and lengthy application process of field-applied powder epoxy coatings.
 
Features & Specifications
Basic Use
TC 7025 EZ Flow Epoxy is a corrosion preventive epoxy coating developed for coating joints, patching pipeline coatings or coating irregular fittings and surfaces; suitable for above and below ground applications.
Composition
TC 7025 EZ Flow Epoxy is a 100% solids epoxy.
Technical Data at 25 mils
VOC
0 lbs/gal (0 kg/L)
Solids
100% by volume
Coverage
64 ft2/gal (25 mils)/1.57 m2/liter (0.635 mm)
Time to backfill at 80°F
4 hours
Application temperature
40ºF-120ºF (4ºC-49ºC)
Operating temperature
-40ºF to 165ºF (-40ºC to 74ºC)
Thickness
25 mils (0.635 mm)
Weight per Gallon
13.6 lbs (6.16 kg)
Surface Preparation
Remove all contaminants that would impede bond. Use effective cleaning procedures to remove: moisture, salts, rust, dirt and dust, oil and grease. This may include the use of high pressure fresh water cleaning, using suitable solvents or detergents to SSPC-SP-1, and abrasive blast to SSPC-SP-6.
Application
Environment: Use only where application and curing can proceed at temperatures above 40ºF (4ºC). The temperature of the surface and that of the coating itself must also be within these limits. Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation. Relative humidity maximum is 90% preferably between 40-60% (See detailed field specificatons for complete instructions.)
Mixing: Pour entire contents of hardener into the resin container and mix thoroughly for approximately 2 to 3 minutes until homogenously mixed.
Application Method: Apply epoxy by brush, pad or roller. For spray application use TC 7025 spray grade epoxy .
Also Available
TC 7000, TC Epoxy Mastic, TC 7030, TC Seapoxy, Tapecoat H35 Gray Tape, Tapecoat  H50, and Tapecoat M50RC cold-applied coatings in tape form with integrated primer. Tapecoat 6025 cold-applied coating and TC HTMB in tape form for use in high temperature pipeline service. Tapecoat T–Tape Gray PE cold-applied coating for difficult-to-wrap areas.
 


您最近浏览的商品

美国泰亚赛褔